1. POWER Press the I/O button to power up the controller (the blue indicator will light up). A second press will power the controller OFF.
Press the Power button to turn the controller ON. Indicators TEMP, TIMER, PEMF, and PHOTON will light up on the screen. A second press will turn the controller OFF.
2. TEMPERATURE Set and Adjust Press the TEMP button once to activate the heat (timer will be activated simultaneously). Press the TEMP button again to enter temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press the TEMP button again to save the setting.
TEMP -> TEMP -> + or – -> TEMP*
Once the temperature indicator stops flashing, it will display the actual temperature measured at the core of the mat after 5 seconds.
3. TIMER Set and Adjust Press the TIME button to enter timer adjustment mode (the time indicator will start flashing). Set the desired time (0:01, 0:02, … 0:59, 1:00, 2:00, … 12:00) and press the TIME button again to save the setting. The timer and heat will automatically turn off when the countdown reaches 0:00.
TIME -> + or – -> Time*
4. PHOTON LIGHT On/Off Press the PHOTON button to turn the lights ON or OFF (the screen will display the light operating time countdown). Press & hold the TIME button to enter the light operating time adjustment mode (the PHOTON indicator will start flushing). Set the time (1 to 9 hrs), and press the TIME button again to save the setting. The light will automatically turn off when the countdown reaches 0:00.
PHOTON -> TIME -> + or – -> Time*
5. MEMORY MODE
Press the M1 to M4 buttons to activate a memorized mode. The screen will display the selected mode along with the corresponding temperature, time, and photon settings (see factory presets below).
To adjust settings, follow the instructions provided above. To save new settings press & hold the corresponding M-button for 5 sec (a flashing blue indicator will confirm the successful update).
6. °F or °C Units Set Press and hold TEMP button for 6 sec to switch between Fahrenheit and Celsius
7. FACTORY RESET When the controller is turned ON, press & hold the Power button for 10 sec. The controller will shut down and then turn back ON automatically.
8. FACTORY SETTINGS
Mode
Temp
Photon
PEMF
Timer
(activated)
86°F (30°C)
1:00
7,83 Hz**
12:00
M1
Sleep
100°F (38°C)
off
3 Hz
12:00
M2
Relax
110°F (43°C)
off
8 Hz
2:00
M3
Energize
130°F (54°C)
0:30
12 Hz
1:00
M4
Recover
140°F (60°C)
1:00
20 Hz
1:00
E1: Sensor unplugged, or connection lost. E2: Sensor short circuit or mat overheating. E3: Controller overheating. Abn: PEMF coil or heating wire disconnected. The indicator will flash for 5 sec, then vanish, all other functions will operate normally.
*Pressing any key will save the setting and exit adjustment mode; however, it is recommended to develop a habit of using buttons relevant to the function being adjusted
**Displayed as 8 Hz.
INFORMATION • Upon activation, each function will operate based on the factory preset or the most recently saved settings. • If there is no action for 5 seconds while in a function adjustment mode, the last displayed setting will be saved, and the adjustment mode will exit. • Press and hold + or – to reach desired numbers faster. • PHOTON can be turned on or off at any time with or without heat. • If there is no action for 5 min, the controller will dim and enter sleep mode (activated functions will continue to operate). Press any button to wake the screen. • The controller is universal for 110V and 220V.
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the Power button to turn ON the controller. TEMP and TIMER indicators will light up on the screen.
2. TEMPERATURE Set and Adjust Press TEMP button once to turn HEAT ON. Press TEMP again to initiate temperature adjustment mode (temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.
TEMP -> TEMP -> + or – -> TEMP
3. TIMER Set and Adjust Press TIME button to initiate time adjustment mode ( time indicator will start flashing). Set the desired time and press TIME button again to save the setting.
TIME -> + or – -> Time
4. °F or °C Units Set Press and hold TIME button for 6 sec to switch between Fahrenheit and Celsius
5. FACTORY RESET Press and hold POWER button for 10 sec. The controller will shut down and turn back ON automatically
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the Power button to turn ON the controller. TEMP and TIMER indicators will light up on the screen.
2. TEMPERATURE Set and Adjust Press TEMP button once to turn HEAT ON. Press TEMP again to initiate temperature adjustment mode (temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.
TEMP -> TEMP -> + or – -> TEMP
3. TIMER Set and Adjust Press TIME button to initiate time adjustment mode ( time indicator will start flashing). Set the desired time and press TIME button again to save the setting.
TIME -> + or – -> Time
4. PEMF Set and Adjust Press PEMF button once to turn PEMF ON. Press PEMF again to initiate PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (1-30 Hz) and press PEMF button again to save the setting.
PEMF -> PEMF -> + or – -> TEMP
Press and Hold PEMF button for 6 sec to turn PEMF OFF
5. °F or °C Units Set Press and hold TIME button for 6 sec to switch between Fahrenheit and Celsius
6. FACTORY RESET Press and hold POWER button for 10 sec. The controller will shut down and turn back ON automatically
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the Power button to turn ON the controller. TEMP and TIMER indicators will light up on the screen.
2. TEMPERATURE Set and Adjust Press TEMP button once to turn HEAT ON. Press TEMP again to initiate temperature adjustment mode (temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.
TEMP -> TEMP -> + or – -> TEMP
3. TIMER Set and Adjust Press TIME button to initiate time adjustment mode ( time indicator will start flashing). Set the desired time and press TIME button again to save the setting.
TIME -> + or – -> Time
4. PHOTON LIGHT Set Press PHOTON button to turn lights ON or OFF
5. °F or °C Units Set Press and hold TIME button for 6 sec to switch between Fahrenheit and Celsius
6. FACTORY RESET Press and hold POWER button for 10 sec. The controller will shut down and turn back ON automatically
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the Power button to turn ON the controller. TEMP and TIMER indicators will light up on the screen.
2. TEMPERATURE Set and Adjust Press TEMP button once to turn HEAT ON. Press TEMP again to initiate temperature adjustment mode (temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.
TEMP -> TEMP -> + or – -> TEMP
3. TIMER Set and Adjust Press TIME button to initiate time adjustment mode ( time indicator will start flashing). Set the desired time and press TIME button again to save the setting.
TIME -> + or – -> Time
4. PEMF Set and Adjust Press PEMF button once to turn PEMF ON. Press PEMF again to initiate PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (1-30 Hz) and press PEMF button again to save the setting.
PEMF -> PEMF -> + or – -> TEMP
Press and Hold PEMF button for 6 sec to turn PEMF OFF
5. PHOTON LIGHT Set Press PHOTON button to turn lights ON or OFF
6. °F or °C Units Set Press and hold TIME button for 6 sec to switch between Fahrenheit and Celsius
7. FACTORY RESET Press and hold POWER button for 10 sec. The controller will shut down and turn back ON automatically
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1.POWER Press the Power button to turn ON the controller.
2.HEAT SETTINGS Press HEAT ON/OFF button once to turn HEAT ON. Then press HEAT MODE button to initiate temperature adjustment mode. Set the desired temperature. To set the desired heat time press HEAT MODE button after you set the desired temperature to initiate heat timer adjustment mode
HEAT ON/OFF -> HEAT MODE (heat settings) -> ⇑H or ⇓H -> HEAT MODE (timer settings) -> H or H
Hold the HEAT MODE button until you hear a BEEP to switch between °F and °C
3.PHOTON SETTINGS Press the PHOTON button to turn ON photon lights. Photon lights turn off automatically after one hour and can be turned on again at any time. Lights operate with or without heat.
4.CHANGEABLE PEMF MODE Press the PEMF ON/OFF button to turn ON PEMF. Press the PEMF MODE button and ⇑P or ⇓P to adjust settings below:
1. POWER Press the Power button to turn ON the controller. TEMP and TIMER indicators will light up on the screen.
2. TEMPERATURE Set and Adjust Press TEMP button once to turn HEAT ON. Press TEMP again to initiate temperature adjustment mode (temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.
TEMP -> TEMP -> + or – -> TEMP
3. TIMER Set and Adjust Press TIME button to initiate time adjustment mode (time indicator will start flashing). Set the desired time and press TIME button again to save the setting.
TIME -> + or – -> Time
4. PEMF Set and Adjust Press PEMF button once to turn PEMF ON. Press PEMF again to initiate PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (1-30 Hz) and press PEMF button again to save the setting.
PEMF -> PEMF -> + or – -> TEMP
Press and Hold PEMF button for 6 sec to turn PEMF OFF
5. PHOTON LIGHT Set Press PHOTON button to turn lights ON or OFF
6. °F or °C Units Set Press and hold TIME button for 6 sec to switch between Fahrenheit and Celsius
7. FACTORY RESET Press and hold POWER button for 10 sec. The controller will shut down and turn back ON automatically
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the I/O button to power up the controller (the blue indicator will light up). A second press will power the controller OFF.
Press the Power button to turn the controller ON. Indicators TEMP, TIMER, PEMF, and PHOTON will light up on the screen. A second press will turn the controller OFF.
2. TEMPERATURE Set and Adjust Press the TEMP button once to activate the heat (timer will be activated simultaneously). Press the TEMP button again to enter temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press the TEMP button again to save the setting.
TEMP -> TEMP -> + or – -> TEMP*
3. TIMER Set and Adjust Press the TIME button to enter timer adjustment mode (the time indicator will start flashing). Set the desired time (0:01, 0:02, … 0:59, 1:00, 2:00, … 12:00) and press the TIME button again to save the setting. The timer and heat will automatically turn off when the countdown reaches 0:00.
TIME -> + or – -> Time*
4. PEMF Set and Adjust Press the PEMF button once to activate PEMF. 2nd press activates PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (0.25, 0.5, 1, … 30 Hz) and press the PEMF button again to save the setting. The 3rd press (after the adjustment mode exit due to any button press (including the PEMF button) will deactivate PEMF function.
PEMF -> PEMF -> + or – -> TEMP*
PEMF is set as cycles of 20 min on and 100 min off until PEMF is turned OFF or TIMER countdown reaches 0:00.
5. PHOTON LIGHT Set Press the PHOTON button to turn the lights ON or OFF (the screen will display the light operating time countdown). Press & hold the TIME button to enter the light operating time adjustment mode (the PHOTON indicator will start flushing). Set the time (1 to 9 hrs), and press the TIME button again to save the setting. The light will automatically turn off when the countdown reaches 0:00.
6. MEMORY MODE
Press the M1 to M4 buttons to activate a memorized mode. The screen will display the selected mode along with the corresponding temperature, time, PEMF, and photon settings (see page 2 for factory presets).
To adjust settings, follow the instructions provided above. To save new settings press & hold the corresponding M-button for 5 sec (a flashing blue indicator will confirm the successful update).
7. °F or °C Units Set Press and hold TEMP button for 6 sec to switch between Fahrenheit and Celsius
8. FACTORY RESET When the controller is turned ON, press & hold the Power button for 10 sec. The controller will shut down and then turn back ON automatically.
9. FACTORY SETTINGS
Mode
Temp
Photon
PEMF
Timer
(activated)
86°F (30°C)
1:00
7,83 Hz**
12:00
M1
Sleep
100°F (38°C)
off
3 Hz
12:00
M2
Relax
110°F (43°C)
off
8 Hz
2:00
M3
Energize
130°F (54°C)
0:30
12 Hz
1:00
M4
Recover
140°F (60°C)
1:00
20 Hz
1:00
E1: Sensor unplugged, or connection lost. E2: Sensor short circuit or mat overheating. E3: Controller overheating. Abn: PEMF coil or heating wire disconnected. The indicator will flash for 5 sec, then vanish, all other functions will operate normally.
*Pressing any key will save the setting and exit adjustment mode; however, it is recommended to develop a habit of using buttons relevant to the function being adjusted
**Displayed as 8 Hz.
INFORMATION • Upon activation, each function will operate based on the factory preset or the most recently saved settings. • If there is no action for 5 seconds while in a function adjustment mode, the last displayed setting will be saved, and the adjustment mode will exit. • Press and hold + or – to reach desired numbers faster. • PEMF/PHOTON can be turned on or off at any time with or without heat. • If there is no action for 5 min, the controller will dim and enter sleep mode (activated functions will continue to operate). Press any button to wake the screen. • The controller is universal for 110V and 220V.
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Press the I/O button to power up the controller (the blue indicator will light up). A second press will power the controller OFF.
Press the Power button to turn the controller ON. Indicators TEMP, TIMER, PEMF, and PHOTON will light up on the screen. A second press will turn the controller OFF.
2. TEMPERATURE Set and Adjust Press the TEMP button once to activate the heat (timer will be activated simultaneously). Press the TEMP button again to enter temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press the TEMP button again to save the setting.
TEMP -> TEMP -> + or – -> TEMP*
Once the temperature indicator stops flashing, it will display the actual temperature measured at the core of the mat after 5 seconds.
3. TIMER Set and Adjust Press the TIME button to enter timer adjustment mode (the time indicator will start flashing). Set the desired time (0:01, 0:02, … 0:59, 1:00, 2:00, … 12:00) and press the TIME button again to save the setting. The timer and heat will automatically turn off when the countdown reaches 0:00.
TIME -> + or – -> Time*
4. PHOTON LIGHT On/Off Press the PHOTON button to turn the lights ON or OFF (the screen will display the light operating time countdown). Press & hold the TIME button to enter the light operating time adjustment mode (the PHOTON indicator will start flushing). Set the time (1 to 9 hrs), and press the TIME button again to save the setting. The light will automatically turn off when the countdown reaches 0:00.
PHOTON -> TIME -> + or – -> Time*
5. MEMORY MODE
Press the M1 to M4 buttons to activate a memorized mode. The screen will display the selected mode along with the corresponding temperature, time, and photon settings (see factory presets below).
To adjust settings, follow the instructions provided above. To save new settings press & hold the corresponding M-button for 5 sec (a flashing blue indicator will confirm the successful update).
6. °F or °C Units Set Press and hold TEMP button for 6 sec to switch between Fahrenheit and Celsius
7. FACTORY RESET When the controller is turned ON, press & hold the Power button for 10 sec. The controller will shut down and then turn back ON automatically.
8. FACTORY SETTINGS
Mode
Temp
Photon
PEMF
Timer
(activated)
86°F (30°C)
1:00
7,83 Hz**
12:00
M1
Sleep
100°F (38°C)
off
3 Hz
12:00
M2
Relax
110°F (43°C)
off
8 Hz
2:00
M3
Energize
130°F (54°C)
0:30
12 Hz
1:00
M4
Recover
140°F (60°C)
1:00
20 Hz
1:00
E1: Sensor unplugged, or connection lost. E2: Sensor short circuit or mat overheating. E3: Controller overheating. Abn: PEMF coil or heating wire disconnected. The indicator will flash for 5 sec, then vanish, all other functions will operate normally.
*Pressing any key will save the setting and exit adjustment mode; however, it is recommended to develop a habit of using buttons relevant to the function being adjusted
**Displayed as 8 Hz.
INFORMATION • Upon activation, each function will operate based on the factory preset or the most recently saved settings. • If there is no action for 5 seconds while in a function adjustment mode, the last displayed setting will be saved, and the adjustment mode will exit. • Press and hold + or – to reach desired numbers faster. • PHOTON can be turned on or off at any time with or without heat. • If there is no action for 5 min, the controller will dim and enter sleep mode (activated functions will continue to operate). Press any button to wake the screen. • The controller is universal for 110V and 220V.
Please allow up to 40 minutes for the surface to reach the maximum temperature. Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the mat. Press and hold + or – button to reach desired numbers faster.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. POWER Flip the Power switch to turn the mat on. The display will start to show a red light. You can use this switch to turn the power off.
2. TIMER Set and Adjust Press the Time button to choose between 3-hour, 6-hour or 12-hour settings. The green light indicates which time setting is selected.
3. TEMPERATURE Set and Adjust Turn the dial clockwise to increase the temperature and counterclockwise to decrease the temperature from 30°C (85°F) to 70°C (160°F).
4. LED display The red LED display begins by showing the actual temperature. When you start turning the dial it shows your selected temperature for a few seconds, and then goes back to showing the actual temperature. Once the selected temperature is reached, the red display will start showing blinking lines instead of the temperature.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
Before contacting us with an issue regarding your controller, please make sure that you plug your controller deep into the mat’s jack and then fully into a power outlet. If something still seems wrong, send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern. We will help you find the best solution.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. Flip the power switch (№1) On. The display will start to show a red light. You can use this switch to turn the power Off.
2. Press the timer button (№2) to choose between 3-hour (press once), 6-hour (press twice) or 12-hour (press three times) settings. The green light indicates which time setting is selected.
3. Turn the dial (№3) to set your selected temperature from 30°C (85°F) to 70°C (160°F). For extended periods (overnight), 35-40°C is suggested for lighter effects. For shorter sessions, 45-55°C is good to get full therapy or energy. For maximum sauna effect, for about 30 minutes, 60-70°C is ideal.
4. The red LED display (№4) shows the actual temperature. Once you start turning the dial it shows your selected temperature for a few seconds, and then goes back to showing the actual temperature.
5. Press the Photon button (№5) to turn the photon lights On/Off. The lights operate independent of the heat.
6. Press the PEMF button (№6) to turn PEMF On/Off. The PEMF function works independently with or without heat. The PEMF operates at a 20/100 cycle. After you press the button it is on for 20 minutes, then idles for 100 minutes, then again active for 20 minutes. This cycle continues for up to 12 hours or until you press PEMF button Off. To restart another 20 minutes without waiting you can press this button Off then On again.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat's jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
Flip the Power switch (№1) to turn the mat on. The display will start to show a red light. You can use this switch to turn the power off.
Press the Switch/Time button (№2) to choose between 3-hour, 6-hour or 12-hour settings. A green light indicates which time setting is selected.
Turn the dial (№3) clockwise to increase the temperature and counterclockwise to decrease the temperature from 30°C (85°F) to 70°C (160°F).
The red LED display (№4) shows the actual temperature. Once you start turning the dial it shows your selected temperature for a few seconds, and then goes back to showing the actual temperature.
Press the PEMF button (№5) to turn PEMF on or off. The PEMF function works independently with or without heat. When you press the button, the PEMF is on for 20 minutes, then goes off for 100 minutes, then repeats again. To start a fresh 20 minutes you can always turn the PEMF off and then back on.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
First, please plug your controller deep into the mat’s jack and then into a power outlet. This unit is under warranty. If anything happens just send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
Queen and King mats have a controller with separate settings for each side of the mat.
1. POWER Flip the Power switch on. The display will start to show a red light. You can use this switch to turn the power off.
2. TIMER Set and Adjust Press the Time button to choose between 3-hour, 6-hour or 12-hour settings. The green light indicates which time setting is selected.
3. TEMPERATURE Set and Adjust Turn the dial clockwise to increase the temperature and counterclockwise to decrease the temperature from 30°C (85°F) to 70°C (160°F).
4. LED display The red LED display begins by showing the actual temperature. When you start turning the dial it shows your selected temperature for a few seconds, and then goes back to showing the actual temperature. Once the selected temperature is reached, the red display will start showing blinking lines instead of the temperature.
5. PHOTON LIGHT Set Press the Photon button to turn the photon lights on or off. The lights operate independently with or without heat.
6. PEMF Set Press the PEMF button to turn PEMF on or off. The PEMF function works independently with or without heat. When you press the button, the PEMF is on for 20 minutes, then goes off for 100 minutes, then repeats again. To restart the cycle, you can always turn the PEMF off and then back on. The PEMF light stays on even during the 100-minute off phase.
HealthyLine produces almost 100 mat variations with different sizes, power, and functions. We use over a dozen different controllers. If your mat came with a different one, they all work similarly. However, they may not substitute each other even if they fit in the jack. Please DO NOT switch controllers between different mats.
Before contacting us with an issue regarding your controller, please make sure that you plug your controller deep into the mat’s jack and then fully into a power outlet. If something still seems wrong, send us an email to info@HealthyLine.com with a picture of the controller and detailed information about the concern. We will help you find the best solution.
Remember, the mat is made of many functional layers. It takes 5-to-25 minutes for the stones to heat up completely. Keep the mat covered with a blanket and/or lie on the mat to make it heat up faster.
1. Lay your mat down on a flat surface such as a bed, massage table or floor. 2. Slip the optional waterproof cover onto your mat. 3. Plug one end of the controller into your mat and then plug the other end into an outlet. 4. Turn the power on and adjust your timer to choose the desired time.
Suggested Temperature Settings
35-40C: Appropriate if you have conditions sensitive to heat. Also good for extended (overnight) use. Gives deep relaxation. 45-55C: Cycles of 2 hours or more. Good for fitness and flexibility training. Helps with cardio and temporarily increases local blood circulation. 55-65C: Cycles of 30-90 minutes (maximum twice per day) help with tension and anxiety. Increases joint, muscle, and weak tissue support, pain relief, deep relaxation, and mood. Improves the detoxification process. 65-70C: Cycles of 30-60 minutes (maximum once per day) provide sauna-level cleansing and detoxification of heavy metals and cellular waste. Stimulates natural weight loss, aids metabolism, and temporarily improves local blood circulation where applied.
Notes
– Your new purchase comes with a five-year warranty. If you have any concerns, please send us an email to support@HealthyLine.com and we will provide the best possible solution. – For helpful instructional videos, visit HealthyLine.com/video. – EMF shielding is provided on all units. HealthyLine is FDA registered. – Drink more water when you use the mat. The detoxification process requires you to be very hydrated. – A mat lasts much longer if you keep it flat. It is best used on a bed or the floor, but you can move and fold it if needed. – Try to not get the mat wet. It is water-resistant, but if you cover it with our cover or any towel it will generally stay clean. If you need to clean it, unplug it and use a wet towel. – If you enjoy our products please share the news with others. If you need more printed materials to hand out, let us know and we will provide them along with our gratitude. – If you are a professional in a related field or have a blog or social account that may be interested, ask us how to become an affiliate to turn a good experience for you into a good experience for others.